Don't know which Timber Preservative to buy? Let Us help you with our step by step guide to select the best timber treatment.

Aussie Coat

$38.70$232.90 (Inclusive of GST)

Aussie Coat

$38.70$232.90 (Inclusive of GST)

AUSSIE COAT is a long lasting opaque exterior acrylic coating designed for Australia’s harsh climate. It is suitable for use on exterior timber such as outdoor timber furniture, pergolas, ballistrades and railing, cladding, window frames or doors. AUSSIE COAT is a satin or semi-gloss finish and it’s colour approximates that of Spotted Gum on most timber. It is an easily repairable finish, making maintenance a breeze. Please note that this is not recommended for decking.
Clear
SKU: RADIAL SEALER-1 Category:

Recommended Uses

Timber finishes like AUSSIE COAT will protect the timber from weather. It will expand and contract to allow some normal timber movement. Aussie Coat is recommended for popular timbers such as Cedar, Merbau, Cypress Pine, and Australian Hardwoods.

Surface Preparation

Previously painted surfaces must be completely stripped back to bare timber.It is recommended to apply a timber cleaner (oxalic acid) such as Preschem Grey Deck Cleaner followed by power washing the timber surface. Timber with tanin, iron or mould stains needs to be sanded or treated with mould killers such as Preschem D-Mould. This will ensure Aussie Coat has a clean timber surface to adhere to.

IMPORTANT: This product is a timber coating and whilst it does penetrate, it can trap foreign matters left on the timber surface. We cannot guarantee that tanin or mould may not develop under the surface of this coating at a later date. Timber is a natural product and can be unpredictable.

We recommend applying 3 coats with the first coat applied on wet/damp timber.

Directions For Use

Ensure a clean dry surface free from dirt, grease and wax.

Apply the 1st coat of Aussie Coat on wet or damp timber to enhance penetration of the mould aside. Apply liberally and allow to dry. Apply further 2 coats of Aussie Coat.Allow 2 hours between coats and ensure the surface is touch dry prior to recoating. Mix well prior to application and during the application process. The application can be made with a pad type applicator and brushes. HVLP and airless sprayers can also be used for large vertical areas. Use of rollers is not recommended for application. Avoid lap marks by maintaining a wet surface in the application area. Application in temperatures above 32°C or below 8°C is not recommended. Application in direct sunlight may cause poor adhesion. Do not apply too late in the day and be careful of applications where rain may be expected within 6 hours. Surfaces that make contact with Aussie Coat such as doors may be sticky if not let to dry properly before re-contact.

Restoration and Maintenance

The condition of the coating should be assessed every 18 months.

Further coatings should be applied prior to the coating breaking down (cracking or peeling).

Clean area to be re-applied with powerwasher and reapply minimum of 2 coats. The surface can be very slightly moist on the first coat.

If the coating has broken down, it is recommended to strip this back to raw timber before reapplication.

Coverage

Rough Sawn approx 6-8 m 2/Litre.

Dressed approx 12-14 m 2/Litre

Clean Up

Application equipment is cleaned in water.

Packaging

vailable in 1, 4 and 10 litre cans.

Safety Instructions

Avoid skin contact by wearing protective clothing. Don’t breathe vapour or spray mist and provide ventilation. Keep out of reach of children.

First Aid Instructions

If poisoning occurs, contact a doctor or Poison Information Centre (13 11 26).
Eyes
Hold eyes open, flood with water for at least 15 minutes – see a doctor.
Skin
Remove contaminated clothing and wash skin thoroughly with soapy water.
Inhalation
Remove to fresh air.
If Swallowed
DO NOT induce vomiting. Give a glass of water to drink and transport to the hospital.

Additional information

Size

1 LITRE, 4 LITRE, 10 LITRE

Reviews

There are no reviews yet.

Be the first to review “Aussie Coat”

Your email address will not be published. Required fields are marked *